June 2017

On May 19, 2017, the US Consumer Product Safety Commission (CPSC) issued proposed rule 16 CFR 1237 in Federal Register 82 FR 22925 regarding the safety standard adoption for Booster Seats.

In the proposed rule, the newly published ASTM F2640-17e1 Standard Consumer Safety Specification for Booster Seats was adopted in order to reduce the chance of injury associated with booster seats which are defined as:

1. A juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height

2. Made for the purpose of containing a child, up to 5 years of age, and normally for feeding or eating

3. A booster seat that may be height adjustable and include a reclined position

The proposed rule is currently under comment period until August2, 2017.

On May 24, 2017, the Environmental Protection Agency (EPA) issued Final Rule 82 FR 23735 to delay the implementation of 21 CFR Part 770 “Formaldehyde Emission Standards for Composite Wood Products”. The Final Rule 21 CFR 770 was approved and published in the Federal Register on December 12, 2016 to implement standards to reduce formaldehyde emissions as required by the Compliance Monitoring Strategy of the Toxic Substances Control Act (TSCA) (See test).

The implementation timeline is summarized below:

The Final Rule will be effective on July 10, 2017 unless the EPA receives any adverse comment by June 8, 2017.

On April 25, 2017, the Environmental Protection Agency (EPA) issued two notices, 82 FR 19044 and 82 FR 19046. The EPA reports findings on new chemical substances or significant new uses that are not likely to present an unreasonable risk of injury to health or the environment.

The EPA is required under TSCA section 5(g) to publish in the Federal Register a statement of its findings after its review of a TSCA section 5(a) notice when the EPA makes a finding that a new chemical substance or significant new use is not likely to present an unreasonable risk of injury to health or the environment. The two notices present statements of findings during December 2016 and February 2017 separately. The case numbers and the chemical substances that were reviewed are listed below:

Below is a summary of recently updated ASTM standards:

On May 5, 2017, the California Office of Environmental Health Hazard Assessment (OEHHA) issued a notice that Pentabromodiphenyl Ether Mixture [DE-71 (technical grade)] is intended to be listed under Proposition 65 as known to the State to cause cancer.

The chemical details are provided below:

The comment period for listing of Pentabromodiphenyl Ether Mixture intention ended on June 5, 2017.

In 1986, California voters approved an initiative titled California Proposition 65 to address their growing concerns about exposure to toxic chemicals. Since its origin, there have been many lawsuits that have resulted in reformulations of consumer products containing carcinogenic and reproductively harmful chemicals on the Cal Prop 65 list.

Recent 60-day notices from April to May of 2017 include the following:

Beginning January 1, 2018, manufacturers of children’s product sold in the State of Oregon are required to report to the Oregon Health Authority (OHA) if their products contain one or more of 66 High Priority Chemicals of Concern for Children’s Health (HPCCCH) which are at or above the de minimis level. As the reporting date is coming close, a guidance related to exemption has been issued by the OHA to assist manufacturers.

Instead of notifying the OHA, a manufacturer may alternatively submit a request for the reporting exemption if a children’s product contains a HPCCCH as a contaminant at or above the de minimis level. In order to be approved for the exemption, manufacturers must also demonstrate that the contaminant is effectively controlled under a Manufacturing Control Program (MCP). To make it clear, the guidance explains the elements of a MCP that the OHA will evaluate. They include:

1. Manufacturer name, mailing address, contact information

2. Manufacturer should specify if they believe that any confidential business records or trade secrets are included in the MCP

3. The HPCCCHs covered by the MCP

4. Description of the product and description of how and when in the process the HPCCCH is generated

5. Categories MCP is being structured around (manufacturing processes, materials or groups of materials, component parts, or finished products)

6. Description of the mechanisms covered by the MCP

7. Information of best manufacturing practice and process (generally recognized in the industry) that the MCP meets

8. Document and describe manufacturing control practices and processes from point #7

In addition, the OHA will accept exemption requests beginning June 28, 2017.

In May 2017, the European Union (EU) issued and approved Directive (EU) 2017/774 and Directive (EU) 2017/898 to amend the Toy Safety Directive 2009/48/EC in adding a new requirement for Phenol and lowering the limit of Bisphenol A (BPA)

In Directive (EU) 2017/774, the following new entry regarding the limit of phenol will be added to Annex II (Appendix C) of Directive 2009/48/EC:

Beginning from November 4, 2018, toys intended for use by children under 36 months and other toys intended to be placed in the mouth will be subject to the above phenol requirements.

In addition, Directive (EU) 2017/898 made the following changes in the same section of Directive 2009/48/EC regarding the migration limit of BPA:

The new limit will be effective on November 26, 2018.

On April 29, 2017, the European Union (EU) approved and published Commission Regulation (EU) 2017/752 to amend Regulation (EU) 10/2011 on plastic materials and articles intended to come into contact with food.

Upon implementation of the amendment regulation on May 19, 2018, the following changes to the food contact plastic regulation will be implemented:

1. Updated list of authorized monomers, other starting substances, macromolecules obtained from microbial fermentation, additives and polymer product aids to:

   1. Include 6 new entries of substances

   2. Remove verification of compliance by residual content per food contact surface area for 10 substances

2. Transformed food simulant assignment for testing overall migration into table form for clarity (Technically unchanged)

3. Updated information required for the declaration of compliance

Upon implementation of the amendment regulation on May 19, 2019, the following changes on food contact plastic regulation will be implemented:

1. Add new specific migration limits (0.02mg/kg food or food simulant) for Nickel

On May 19, 2017, the European Commission (EC) published the Guidance to Directive 2014/53/EU Radio Equipment Directive (RED), which has been implemented since June 13, 2016.

The guidance document is based on the RED and the new legal framework described in the “Blue Guide 2016”. In conjunction to the Blue Guide, the guidance explains clearly the definition of radio equipment and provides examples which are excluded from the scope of the RED. The guidance also lists out and provides further information on the obligations of different economic operators, such as manufacturer, importer and distributor.

Other than the definition and obligations, the guidance addresses the essential technical requirements applicable to all and other specific types of radio equipment separately and provides a comparison between the current RED and the repealed Radio Equipment and Telecommunications Terminal Equipment Directive (R&TTED).

In Europe, when hazards are identified in consumer products, the products will be recalled and published in the Rapid Alert System, which is updated weekly. The European recalls for April and May 2017 are summarized below:

* Other Hazards include Asphyxiation Hazard, Cut Hazard, Entrapment Hazard, Fire Hazard, Environmental Hazard, Microbial Hazard, Sight Hazard and Suffocation Hazard with a frequency of less than 10.

^ Other Categories include Candles & Burning Items and Accessories, Consumer Chemicals, Footwear, Furniture, Home Electrical Appliances (Hair Dryer, Iron, etc.), Jewelry, Watch or other Fashion Accessories, Personal Protective Equipment (excludes eye protection), Sporting Goods / Equipment and Tools and Hardware, with a frequency of less than 10.

Download the complete Recalls Summary - EU (April and May 2017)

On April 3, 2017, Food (Amendment) No. 2 Regulations 2017 was published through the Federal Government Gazette. The Regulation amends the Food Regulation 1985 and updates the food contact ceramics requirements. The key changes of the Food Regulations are summarized below:

1. Updates the migration limit of Cadmium (Cd) for:

1. Updates the adopted test method standards

The amendment regulation has been in effect since April 15, 2017.

On May 19, 2017, the Hong Kong Administrative Region (HKSAR) Government published in the Gazette the Toys and Children’s Products Safety Ordinance (Amendment of Schedules 1 and 2) Notice 2017. The notice amends the Toys and Children’s Products Safety Ordinance (Cap. 424) to update certain adopted safety standards.

El 18 de abril de 2017 entró en vigor la nueva Norma de Seguridad de Bienes de Consumo 2017 relativa a la ropa de dormir y de día limitada para niños. La norma de seguridad adopta la norma actualizada AS/NZS 1249: 2014 Children's Nightwear and Limited Daywear Having Reduced Fire Hazard y derogará las normas anteriores publicadas en 2007.

A continuación se resumen las principales actualizaciones de los requisitos:

>

Los requisitos actualizados se encuentran actualmente bajo un periodo de transición hasta el 1 de julio de 2019. Por lo tanto, los productos pueden cumplir la norma actual o la actualizada durante este periodo. Sin embargo, las normas actualizadas serán obligatorias después de la transición.