September 2021

In September 2021, the US Environmental Protection Agency (EPA) prepared for publication a draft final rule extending the deadline for compliance with the TSCA Section 6(h) ban on a particular PBT chemical (i.e., phenol, isopropylated phosphate (3:1) (PIP (3:1)) until 8 March 2022. The publication date for the final rule, which will be followed by a 60-day comment period, has not been determined.

Despite EPA’s extensive outreach conducted during development of the PBT rules, some comments from the stakeholders on PIP (3:1) were still received after the rule was finalized. In response to this, the EPA issued a 180-day “No Action Assurance” in March 2021 to ensure that the supply chain was not interrupted and issued a notice requesting further comments and information on the impact of the compliance dates until 4 September 2021. However, a need for varying time frames to remove PIP (3:1) from the supply chains has been identified. The EPA will issue a final rule (follow by a 60-day comment period) providing a short-term extension of compliance dates until 8 March 2022.

PIP (3:1)-containing articles covered by the short-term compliance date extension include cellular telephones, laptop computers and other electronic devices. In addition, articles that might be used in industrial and commercial equipment used in various sectors including transportation, life sciences, and semiconductor production, as well as other consumer and commercial goods are included.

At the same time, the EPA announced its intent to initiate a new rulemaking and anticipates proposing new rules for all five PBT chemicals that are the subject of final risk management rules under TSCA in the Spring of 2023. The current provisions of the final risk management rules, except the extension of the specified compliance dates for PIP (3:1), remain in effect while the EPA is working on this new rulemaking effort.

Below is a summary on the potential usage, scope, requirement, and effective date for the five PBT chemicals.

In the US, when hazards are identified in consumer products, they will be recalled and published in the Consumer Product Safety Commission (CPSC) Recent Recalls on the CPSC website, which is updated daily. The US recalls from 01 August 2021 to 31 August 2021 are summarized below:

*Other Hazards include Burn Hazard, Amputation Hazard, Laceration Hazard, Pinching Hazard, Entrapment Hazard, Health Risk Hazard, Crash Hazard, Skin Irritation Risk, Drowning Hazard and Exploding Hazard with a frequency of less than 2.

*Other Categories include Outdoor Living Items, Tools and Hardware, Electrical Appliances, Furniture, Stationery and Fabric / Textile / Garment / Home Textile with a frequency of less than 2.

For a complete list click here

In Canada, when hazards are identified in consumer products, they will be recalled and published in the Recalls and Safety Alerts Database on the Health Canada website, which is updated daily. The Canada recalls from 01 August 2021 to 31 August 2021 are summarized below:

*Other Hazards include Swallowing Risk, Injury Hazard and Crash Hazard with a frequency of less than 2.

*Other Categories include Household Items and Food Contact Material with a frequency of less than 2.

For a complete list click here

Four proposals to identify new SVHCs were published on 3 September 2021. They are under public consultation and available for comments until 18 October 2021.

This is the second batch of proposals to identify SVHCs in 2021. The first batch of proposals with eight substances was published in March; all of them were included in the current SVHCs candidate list with 219 substances in July. The candidate list is updated two times a year, generally at the beginning and in the middle of a year.

The four substances in this new batch of proposals that might be included in the upcoming update of the SVHC candidate list (expected in early January 2022) are listed below. The candidate list would increase to 223 substances if all of them are included.

On 28 July 2021, the European Commission (EC) published Notification 2021/0513/I on Italy’s intention to expand the positive list of food contact stainless steels.

Italy proposes to adopt a draft legislation on food contact stainless steels and the European Commission (EC) published Notification 2021/0513/I on Italy’s intention on 28 July 2021. If the draft legislation is adopted, it will amend the Decree of the Minister of Health of 21 March 1973, in relation to food contact stainless steels.

According to the Notification, there are two important changes addressed:

• Adding one more type of stainless steel to the positive list - UNI EN 10088-1: 2014 Numerical designation 1.4062, also known as AISI/ASTM A240 or UNS 32202

• Adding one specification for the concentration of certain elements in food contact stainless steels without codes or designations

In addition, the three months standstill period will end on 29 October 2021.

In May 2021, the European Directorate for the Quality of Medicines & HealthCare (EDQM) published the first edition of the technical guide entitled “Paper and board used in food contact materials and articles”.

In the absence of specific EU legislation on food contact paper and board, the EDQM published the first edition of technical guidance on “Paper and board used in food contact materials and articles’’.This guidance aims to improve the protection of consumers against contaminants potentially released by paper and board in contact with food.

This guidance includes two aspects:

• Part I. Council of Europe Resolution CM/Res (2020) 9 on the safety and quality of materials and articles for contact with food

• Part II. Technical guide on paper and board used in food contact materials and articles

On 31 July 2021, the European Committee for Standardization (CEN) published a new European standard of seating for children (EN 17191:2021) which supports EU Directive 2001/95/EC. The effective date is January 2022.

The European standard of seating for children (EN 17191:2021) has been prepared under a standardization request given to the CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU Directive 2001/95/EC.

This standard specifies safety requirements, test methods and labelling requirements for children’s seating products intended to be placed on the floor, for use in both domestic and non-domestic settings, including day care centers, as well as for indoor and outdoor use. The requirements are specifically intended for children who are able to walk and sit by themselves.

This standard does not apply to children’s highchairs or childcare articles such as reclined cradles and seating in educational institutions for which other European standards exist.

In additional to meeting the safety criteria of EN17191, seating for children also needs to comply with flammability requirements (EN71 Part 2) and chemical requirements (EN71 Part 3).

In Europe, when hazards are identified in Non-food Consumer Products, the Products will be recalled and published in the Safety Gate system, which is updated weekly. The European recalls from 01 August 2021 to 31 August 2021 are summarized below:

*Other Hazards include Strangulation Hazard, Environmental Hazard, Cut Hazard and Fire Hazard with a frequency of less than 3.

*Other Categories include Bodycare / Cosmetics, Pet Items, Household Items, Outdoor Living Items, Sporting Goods / Equipment, Stationery and Chemicals with a frequency of less than 4.

*Other Countries include Slovakia, Croatia, Czechia, Romania, Slovenia, Spain and Bulgaria with a frequency of less than 4.

For a complete list click here

South Korea Ministry of Trade, Industry and Energy (MOTIE) Notice No. 2021 - 132 was published on July 2021 to strengthen the phthalates restriction as specified in the “Common Safety Standards for Children's Products” from six phthalates to seven by including DIBP for children’s products. The effective date is 1 January 2022.

The table below is a summary of the amended phthalates requirement within (MOTIE) Notice No. 2021 - 132.

Standard GB 40165-2021, Lithium-ion batteries and battery packs for stationary electronic equipment has been recently released. The release date of GB 40165 was 30 April 2021, and the implementation date is 01 May 2022 which means there is a one-year transition period. After the transition period, products that meet the scope of this standard must meet the requirements of this standard.

The fixed electronic equipment covered by GB 40165 includes:

1. Stationary information technology equipment (IT equipment);

2. Fixed audio and video equipment (AV equipment) and similar equipment;

3. Fixed communication technology equipment (CT equipment);

4. Stationary measurement control and laboratory electronic equipment and similar equipment.

In addition to lithium-ion battery packs for the above equipment, it is also suitable for lithium-ion batteries and battery packs for uninterruptible power supply (UPS) and emergency power supply (EPS).Main test items are outlined below:

http://www.bzfyw.com/search/default.html?page=1&keyword=GB%2040165

The new standard, GB/T 40270-2021, sets out general technical requirements based on consumers' experience and is applicable to direct-to-consumer end textile products for consumption and household use.

The National Standard GB/T 40270-2021 " General technical requirements based on consumer experience " specifically considers the standards from the perspective of consumer experience with textile products such as clothing and home use textiles, based on consumers' sense of touch, vision, and smell, etc. The characteristics of subjective perception can directly reflect the feelings and needs of consumers. The standard outlines consumer demand-oriented practices and standardizes testing parameters to help ensure consumers have a good experience and to prevent an unpleasant experience as it relates to textile products. The standard should not be used as requirements for certain types of products, nor is it recommended to be used as a basis for product quality supervision and public comparisons.

The basic safety requirements of textile products should comply with GB 18401 or GB 31701, and quality requirements should meet the corresponding product standards.

In China, when hazards are identified in consumer products, they will be recalled and published in the SAMR Defective Product Administrative Centre, which is updated daily. The China recalls from 01 August 2021 to 31 August 2021 are summarized below:

*Other Categories include Furniture, Tools and Hardware and Footwear with a frequency of less than 2.

*Other Provinces include Tianjin, Hubei, Guangdong and Beijing with a frequency of less than 2.

** The province of the recall case, Motorcycle Reflexor Part on 13th August is not specified.

For a complete list click here

El 3 de agosto de 2021, la Comisión Australiana de Competencia y Consumo (ACCC) adoptó la norma de modificación para juguetes de proyectil que incorpora las actualizaciones realizadas recientemente a las normas voluntarias australiana/neozelandesa (AS/NZS ISO 8124.1) e internacional (ISO 8124.1), además de otras actualizaciones menores.

A continuación se presenta un resumen de las principales enmiendas a la Norma de Seguridad 2021 de los Bienes de Consumo Australianos (Juguetes de Proyectil):

Actualización de requisitos:

1. La norma australiana / neozelandesa e internacional publicó enmiendas a la norma de ensayo; las enmiendas se adoptan en esta actualización

2. Actualización del periodo transitorio a "24 meses" (a partir del 12 de junio de 2020)

3. Declaración omitida, "ir acompañado de instrucciones de uso que informen al usuario sobre cómo utilizar el juguete de forma segura" (véase B.2.15, juguetes de proyectiles, como orientación). Este requisito sólo se aplica a los proyectiles en los que pueda ser razonablemente posible apuntar a la cara (véase E.32, juguetes proyectiles)

4. Se ha añadido la cláusula 4.19.1 de la Norma Internacional para la modificación de la seguridad de los juguetes omitiendo "Los juguetes voladores teledirigidos irán acompañados de instrucciones que proporcionen al usuario información sobre cómo utilizar el juguete de forma segura" (véase B.2.26.2).

Actualización de los requisitos de advertencia:

Sección 13(1)Esta sección se aplica a un juguete proyectil si cumple todo lo siguiente:

1. Podría ser razonablemente posible apuntar el juguete proyectil a los ojos o a la cara;

2. El juguete proyectil es capaz de lanzar un proyectil de más de 300 milímetros;

3. El juguete proyectil es capaz de lanzar un proyectil con una energía cinética superior a 0,08J.

Sección 13(2)Se ha suprimido "y el envase" y se ha sustituido por "o el envase".

Sección 13(3)Determinación del alcance del proyectil y de la energía cinética

A efectos de la subsección (1), para determinar si:

1. Un juguete proyectil capaz de lanzar un proyectil de más de 300 milímetros; o

2. Un juguete proyectil es capaz de lanzar un proyectil con una energía cinética superior a 0,08J;

El proveedor debe utilizar la norma en la que se basan los requisitos que pretende cumplir.

En Australia, cuando se identifican peligros en los productos de consumo, se retiran y se publican en la base de datos de retiradas y alertas de seguridad del sitio web de la Comisión Australiana de Competencia y Consumo, que se actualiza diariamente. A continuación se resumen las retiradas de Australia desde el 1 de agosto de 2021 hasta el 31 de agosto de 2021:

*Otros Peligros incluyen Peligro de Incendio, Peligro de Quemaduras, Peligro de Asfixia y Peligro de Descarga Eléctrica con una frecuencia inferior a 3.

*Otras categorías incluyen Electrodomésticos, Artículos para el hogar, Ordenadores / Audio / Vídeo / Otros aparatos electrónicos y accesorios y Farmacia con una frecuencia inferior a 2.

Para consultar la lista completa, pulse aquí